Getting Started with Plumbing Basics for Bathtub Installation
Getting Started with Plumbing Basics for Bathtub Installation
Blog Article
We have found the article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround below on the internet and felt it made perfect sense to share it with you on my blog.
Mounting a bathtub isn't precisely brain surgery, yet it does require strong plumbing, carpentry, and also often, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a reasonably tough job. If the old tub is conveniently available, the task can move easily; if you need to open up a wall to get rid of the old bathtub as well as position the brand-new bathtub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will certainly need an assistant to move out the old bathtub as well as set in the brand-new one. Make sure you have actually qualified on your own for the work and also are comfortable trying it. Rather than employing a contractor to take over a halfway-completed task, it is far better to take into consideration using one before you begin. Possibilities are you might require a professional plumber to make tube links.
This write-up will certainly help you set up a new tub in your shower room if you have actually already purchased a new tub and also don't require to change the setup of your previous water supply pipes.
Your devices as well as material checklist ought to consist of the following:
Getting ready for the Installment
Firstly, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to see to it that if the faucet includes a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the faucets unit to avoid strain on the bath tub.
Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must currently prepare to be fitted in its last position.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installment, then the first thing you must do is disconnect the water supply. After doing so, turn on the faucets to drain any type of water staying in the system. The procedure of removing the existing faucets can be quite problematic as a result of the limited gain access to that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a cloth all set for the remaining water that will originate from the pipes. As soon as the supply pipes have actually been removed, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Before carrying on to fit the new faucets, contrast the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Tub
Utilizing both wooden boards under its feet, position the bath tub in the required position. The wood boards are valuable in equally spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four little factors.
The next objective is to make certain that the tub is leveled all round. This can be achieved by inspecting the spirit level and adjusting the feet on the bathtub till the level reads degree.
To set up faucets, fit the bottom of the outermost versatile tap adapter to the ideal supply pipeline by making a compression join; then do the exact same for the various other tap.
Activate the supply of water and examine all joints and also new pipework for leakages and also tighten them if needed. Fill the tub as well as additionally inspect the overflow outlet and the normal electrical outlet for leakages.
Lastly, repair the bath paneling as described in the maker's instruction manual. Tiling and securing around the tub ought to wait until the bathtub has actually been used a minimum of once as this will certainly settle it right into its final placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to prevent damages to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end supplies a link to the current supply pipes.
If you need to fit a monobloc, then you will call for reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washers are in location in between the faucet and also the sink. Secure the tap in place with the maker provided backnut. Once the tap is safely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet adapters. The previous kind ought to be attached to the tap finishes initially, tightening up just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to break a rigid seal, creating the water to permeate the wall surface between the bathroom as well as the tiling, leading to issues with dampness as well as feasible leaks to the ceiling listed below.
You can pick from a selection of coloured sealants to assimilate your fixtures as well as installations. They are marketed in tubes and also cartridges, and also are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly fill the bathtub with water prior to sealing, to enable the motion experienced when the tub is in use. The sealant can break rather early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also quickly available on the marketplace. It is recommended to fit the ceramic tiles using water-resistant or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate more info about Installing A Bathtub? Try to leave feedback down the page. We'd be interested to listen to your opinion about this content. We hope that you come back again later on. Loved our article? Please share it. Let someone else find it. Thanks for taking the time to read it.
Burst issue? Contact. Report this page